KL03E – Amana Control Panel Security Key Lock For PTAC
Request a Quote
KL03E
Amana KL03E – Control Panel Security Key Lock For PTAC
In conjunction with the tamper-resistant front, the installation of Amana® brand security key locked security controls cover, prevents tampering with the controls used to set temperature, heating and cooling functions.
KEY FEATURES
- Prevents tampering with the controls
- To be used in conjunction with the tamper-resistant front
FK10B – Amana B Series PTAC Unit Filter – 10 Pack
Request a Quote
FK10B
Amana Air Filter Kit FK10B – 10 Pack – B Series
Amana’s FK10B Filter Pack contains 10 replacement filters. Each filter, which is made using synthetic material or electro charged polypropylene, must be installed at the air intake point. These Amana PTAC filters allows air to pass through without any restrictions. On its way through, it traps dust and undesirable pollutants from getting into the air that is blown into the room. This 10 pack of replacement filters for Amana PTAC units will greatly reduce the intake of dirt, lint and other unwanted debris from entering the air circulation. Keeping this grim off the inner coils will greatly increase your unit’s efficiency.
KEY FEATURES
- Fits “B” Series models
- Will also fit “C” & “D” Series PTAC Units
- Filter can easily be removed from the front panel.
- Can be cleaned and reused for up to 4 times.
- Long lasting
FK10E – Amana Filter Kit for E & G Series – 10 Pack
Request a Quote
FK10E
Amana FK10E – Filter Kit for E & G Series – 10 Pack
This Amana air filter replacement pack comes with 10 brand new filters and is made for Amana PTAC units. Replacing the PTAC air filter unit will keep dirt and lint out of the air and off the coils, greatly increasing the energy efficiency of your unit. Fits all E and G series Amana PTAC units.
Replacing is easy! The filter can be found in the front panel of the unit and can also be cleaned and reused up to 4 times.
KEY FEATURES
- For Amana E & G Series PTAC units
- Can be cleaned and reused up to 4 times
- 10 pack
- Amana R410A Filter Kit
- Helps keep dirt and lint out of the air and off the coil, increasing unit efficiency.
- Located in the front panel of the unit
- Easily removable filter.
DGK1B – Amana Condenser Baffle Kit
Request a Quote
DGK1B
Amana DGK1B – Condenser Baffle Kit
For use on non-baffled grilles.
Includes 2 air-deflection baffles that can be mounted on the condenser coil to direct air toward the center and away from the inlet. This prevents the recirculation of hot condenser air, maintaining unit cooling and heating capacity and unit efficiency. Use the baffles when an older unit is being replaced and when the existing grille does not have deflector baffles. Any existing baffles must be removed to install this kit.
KEY FEATURES
- For use on non-baffled grilles
- Includes 2 air-deflection baffles that can be mounted on the condenser coil
- Prevents the recirculation of hot condenser air
PTCB10E – Amana Curtain Baffle Kit for R-410A PTAC Units – 10 pack
Request a Quote
PTCB10E
Amana PTCB10E – Curtain Baffle Kit for R-410A PTAC Units – 10 Pack
The Window Curtain Baffle is the perfect add-on accessory for your Amana PTAC unit. It allows you to install your unit directly under a window without having to be concerned with the room curtains interfering with the airflow from the unit. Additionally, you won’t lose airflow up behind the curtains. The curtain baffle also helps to direct the airflow more directly, helping to ensure proper circulation for your space.
KEY FEATURES
- Accessory PTAC Curtain Baffle
- PTAC Accessories Collection
- Color matched polymer curtain baffles prevent curtains from falling into the discharge airflow of the PTAC.
- Helps ensure proper circulation of air within room.
- Efficiency and compressor life are extended.
- Saves energy by reducing run time and wear and tear on components.
PSHW04A – Amana Power Disconnect Switch for 265 Volts
Request a Quote
PSHW04A
Amana PSHW04A – 265 Volt Power Disconnect Switch
A power disconnect switch can be installed in the optional Standard. Subbase or in the junction box of the Hard Wire Kit. The switch provides a Power On/Off function as required by some electrical codes. Meets NEC requirements.
KEY FEATURES
- For Use With PTC and PTH
PSHW03A – Amana Power Disconnect Switch for 208/230 Volts
Request a Quote
PSHW03A
Amana PSHW03A – 208/230 Volt Power Disconnect Switch
A power disconnect switch can be installed in the optional Standard. Subbase or in the junction box of the Hard Wire Kit. The switch provides a Power On/Off function as required by some electrical codes. Meets NEC requirements.
KEY FEATURES
- For Use With PTC and PTH
PTSB430E – Amana Subbase Kit for 265 Volt – 30 amp
Request a Quote
PTSB430E
Amana PTSB430E – 265 Volt Subbase Kit – 30 Amp
The fully skirted PTSB430E subbase conceals wiring while providing strong support, if needed. Plug-in receptacle and field-wiring access speeds installation. Electrical accessories, such as fuse holders, circuit breakers and disconnect switches meet NEC requirements. Subbase may be installed onto wall sleeve either before or after sleeve installation. Minimum clearance between wall sleeve bottom and finished floor is 3 3/4″; maximum height clearance from bottom of wall sleeve and finished floor is 5″. Minimum clearance between wall sleeve flange and finished wall is 2 3/4″. Inquire about this Amana PTAC Skirted Subbase Kit today!
KEY FEATURES
- For 30 Amp unit
- Required for 265V unit
- Fully skirted sub-base
- Conceals wiring
- Provides strong support
PTSB420E – Amana Subbase Kit for 265 Volt – 20 amp
Request a Quote
PTSB420E
Amana PTSB420E – 265 Volt Subbase Kit – 15/20 Amp
The fully skirted PTSB420E subbase conceals wiring while providing strong support, if needed. Plug-in receptacle and field-wiring access speeds installation. Electrical accessories, such as fuse holders, circuit breakers and disconnect switches meet NEC requirements. This Amana PTAC subbase may be installed onto wall sleeve either before or after sleeve installation. Minimum clearance between wall sleeve bottom and finished floor is 3 3/4″; maximum height clearance from bottom of wall sleeve and finished floor is 5″. Minimum clearance between wall sleeve flange and finished wall is 2 3/4″. Order the PTSB420E Amana PTAC subbase kit today.
KEY FEATURES
- For 15/20 Amp unit
- Required for 265V unit
- Fully skirted sub-base
- Conceals wiring
- Provides strong support
PTSB330E – Amana Subbase Kit for 208/230 Volt – 30 amp
Request a Quote
PTSB330E
Amana PTSB330E – 208/230 Volt Subbase Kit – 30 Amp
The fully skirted subbase conceals wiring while providing strong support, if needed. Plug-in receptacle and field-wiring access speeds installation. Electrical accessories, such as fuse holders, circuit breakers and disconnect switches meet NEC requirements. Subbase may be installed onto wall sleeve either before or after sleeve installation. Minimum clearance between wall sleeve bottom and finished floor is 3 3/4″; maximum height clearance from bottom of wall sleeve and finished floor is 5″. Minimum clearance between wall sleeve flange and finished wall is 2 3/4″.
KEY FEATURES
- For 30 Amp Units
- Required for 208/230 Volt unit
- Fully skirted sub-base
- Conceals wiring
- Provides strong support